|
|
|
|
Chemical Resistance Guide
(Based on 12 month immersion test)
|
The following is a partial list of chemicals which are considered corrosive to many materials but are easily handled by properly installed HORTONCRETE. However, because performance may be affected by varying combinations, concentrations and temperatures, where there is any question of suitability, prior testing of HORTONCRETE is recommended.
Acetic Acid, to 50% Lactic Acid Acetone Lard Acrylic Acid Magnesium Chloride Acrylonitrile Magnesium Nitrate Alum Magnesium Sulfate Aluminum Sulfate Maleic Acid Ammonium Chloride Methanol Ammonium Nitrate Methyl Alcohol Ammonium Sulfate Methyl Ethyl Ketone Ammonium Hydroxide, to 30% Methyl lsobutyl Ketone Barium Chloride Milk Barium Sulfate Mineral Oil Beer Monochlorobenzene Benzene Nickel Chloride Benzenesulfonic Acid, to 10% Nickel Nitrate Benzoic Acid Nickel Sulfate Benzyl Chloride Oleic Acid Black Liquor Oxalic Acid Bleaching Liquor, below 2% Perchloroethylene Boric Acid Petroleum Butyl Acetate Phosphoric Acid Butyl Alcohol Phosphorus Oxychioride Butyric Acid Potassium Chloride Calcium Chloride Potassium Nitrate Calcium Hydroxide Potassium Sulfate Calcium Nitrate Pulp Mill Liquors Calcium Sulfate Sodium Bicarbonate Carbon Disulfide Sodium Carbonate Carbon Tetrachloride Sodium Chloride Chioroacetic Acid, to 10% Sodium Nitrate Chloroform Sodium Phosphate Chloroisobutane Sodium Sulfate Chlorophenol Sodium Sulfide Citric Acid, to 40% Stannic Chloride Copper Chloride Stearic Acid Copper Nitrate Sugar Copper Sulfate Sulfur Dioxide Dichloroethane Sulfuric Acid, to 65% Dimethyl Dialkyl Sulfurous Acid, to 10% Ammonium Chloride Tall Oil Ethanol Thionyl Chloride Ether Toluene Ethyl Acetate Toluenesulfonic Acid Ethyl Alcohol Tomato Juice Ethylene Glycol Trichloroethylene Fatty Acids Trisodium Phosphate Ferric Chloride Turpentine Ferric Nitrate Urea, to 20% Ferric Sulfate Urine Fluorosilicic Acid, to 35% Vegetable Oil Formaldehyde, to 36% Vinegar Formic Acid, to 90% Water, Fresh Grape Juice Water, Distilled Hydrochloric, to 36% Xylene Hydrofluoric Acid Zinc Chloride Jet Fuel Zinc Nitrate Kerosene Zinc Sulfate
|
|
HORTONCRETE will perform satisfactorily in the following splash and spill environments PROVIDED It is sealed after Installation with Hortoncrete Carbon Glaze.
Ammonia Gas Hypochlorous Acid Bromine (free) Phenol, to 30% Calcium Hypochiorite Potassium Hydroxide, to 35°/a Chlorine, to 3O% Potassium Peroxide, to 25% Hydrobromic Acid, to 10% Sodium Hydroxide, to 50% Hydrogen Peroxide, to 10% Sodium Hypochlorite, to 30%
HORTONCRETE is attacked to some degree by the following caustic materials: therefore, its use in these particular environments should be recommended only after careful prior testing.
Aniline Nitric Acid Aqua Regia Othum Chlorosulfonic Acid Phosphorous Bromide Chromic Acid Picric Acid Dimethylformamide (100%) Piperidene (100%) Ethylene Dichloride Pyridine (100%) Methylene Chloride Sulfur Trioxide
* NOTE: While these environments may be corrosive toward HORTONCRETE in high concentrations, performance can be satisfactory with frequent washdowns or where concentrations are low.
WARRANTY INFORMATION: For warranty, limitation of seller’s liability and further product information, please refer to the product data sheet for these products, or contact The Horton Company.
|
U.S. Patent No. 4,373,058
© 1983, The Horton Company
|
 |
 |
 |
|
|
||